LINKSYS-rlInterfaces DEFINITIONS ::= BEGIN

-- Title:      LINKSYS Switch Interfaces Private
-- Version:    7.45
-- Date:       07 May 2006
-- 30-Nov-2004 Added type AutoNegCapabilitiesBits
-- 30-Nov-2004 Added fields swIfAdminSpeedDuplexAutoNegotiationLocalCapabilities
--                          swIfOperSpeedDuplexAutoNegotiationLocalCapabilities
--                          swIfSpeedDuplexNegotiationRemoteCapabilities to swIfEntry
-- 22-Nov-2005 Obsoleted field swIfPhysAddressType
-- 22-Nov-2005 Added rlIfBaseMACAddressPerIfIndex
-- 30-Oct-2005 Added swIfExtTable
-- 30-Nov-2005 Added fields swIfAdminComboMode
--                          swIfOperComboMode swIfExtTable to swIfEntry
-- 05-Dec-2005 Added rlFlowControlCascadeMode and rlFlowControlCascadeType
-- 23-Feb-2005 Added rlFlowControlRxPerSystem
-- 07-May-2006 Added rlCascadePortProtectionAction
-- 04-Jun-2006 Added multiple-auth enum to swIfHostMode
-- 11-Jun-2008 Added rlManagementIfIndex
-- 06-Jun-2009 Added rlIfClearPortMacAddresses

IMPORTS
    rnd, rlIfInterfaces                           	    FROM LINKSYS-MIB
    ifIndex, InterfaceIndex, InterfaceIndexOrZero           FROM IF-MIB
    PortList                                                FROM Q-BRIDGE-MIB
    Unsigned32, Integer32, Counter32,
    MODULE-IDENTITY, OBJECT-TYPE                            FROM SNMPv2-SMI
    RowStatus, TruthValue, TEXTUAL-CONVENTION,
    DisplayString                                           FROM SNMPv2-TC;


swInterfaces MODULE-IDENTITY
      LAST-UPDATED "201304010000Z"  -- April 1, 2013
      ORGANIZATION "Linksys LLC."
      CONTACT-INFO
              "www.linksys.com/business/support"
      DESCRIPTION
              "The MIB module describes the private MIB for Switch Interfaces supported
               by Linksys MTS software and products."      
      REVISION     "201304010000Z"  -- April 1, 2013
      DESCRIPTION
              "Added MODULE-IDENTITY"
      ::= { rnd 43  }
      

-- These bits can be set in any combination (except unknown)
-- for field swIfAdminSpeedDuplexAutoNegotiationLocalCapabilities
-- and will take affect when field swIfSpeedDuplexAutoNegotiation
-- will be set to enabled.
-- In addition these fields can be read for operative values of
-- auto negotiation capabilities
AutoNegCapabilitiesBits ::= TEXTUAL-CONVENTION
    STATUS  current
    DESCRIPTION
        "Auto negotiation capabilities bits."
    SYNTAX BITS {
        default(0),
        unknown(1),
        tenHalf(2),
        tenFull(3),
        fastHalf(4),
        fastFull(5),
        gigaHalf(6),
        gigaFull(7),
        tenGigaFull(8)
    }

--
-- swTable
--

swIfTable    OBJECT-TYPE
   SYNTAX  SEQUENCE  OF SwIfEntry
   MAX-ACCESS   not-accessible
   STATUS       current
   DESCRIPTION
    "Switch media specific information and configuration of the device
     interfaces."
   ::=  { swInterfaces 1 }

swIfEntry OBJECT-TYPE
   SYNTAX  SwIfEntry
   MAX-ACCESS   not-accessible
   STATUS       current
   DESCRIPTION
    "Defines the contents of each line in the swIfTable table."
   INDEX   { swIfIndex }
   ::=  { swIfTable 1 }

SwIfEntry ::= SEQUENCE {
        swIfIndex                                               INTEGER,
        swIfPhysAddressType                                     INTEGER,
        swIfDuplexAdminMode                                     INTEGER,
        swIfDuplexOperMode                                      INTEGER,
        swIfBackPressureMode                                    INTEGER,
        swIfTaggedMode                                          INTEGER,
        swIfTransceiverType                                     INTEGER,
        swIfLockAdminStatus                                     INTEGER,
        swIfLockOperStatus                                      INTEGER,
        swIfType                                                INTEGER,
        swIfDefaultTag                                          INTEGER,
        swIfDefaultPriority                                     INTEGER,
        swIfStatus                                              RowStatus,
        swIfFlowControlMode                                     INTEGER,
        swIfSpeedAdminMode                                      INTEGER,
        swIfSpeedDuplexAutoNegotiation                          INTEGER,
        swIfOperFlowControlMode                                 INTEGER,
        swIfOperSpeedDuplexAutoNegotiation                      INTEGER,
        swIfOperBackPressureMode                                INTEGER,
        swIfAdminLockAction                                     INTEGER,
        swIfOperLockAction                                      INTEGER,
        swIfAdminLockTrapEnable                                 TruthValue,
        swIfOperLockTrapEnable                                  TruthValue,
        swIfOperSuspendedStatus                                 TruthValue,
        swIfLockOperTrapCount                                   INTEGER,
        swIfLockAdminTrapFrequency                              INTEGER,
        swIfReActivate                                          TruthValue,
        swIfAdminMdix                                           INTEGER,
        swIfOperMdix                                            INTEGER,
        swIfHostMode                                            INTEGER,
        swIfSingleHostViolationAdminAction                      INTEGER,
        swIfSingleHostViolationOperAction                       INTEGER,
        swIfSingleHostViolationAdminTrapEnable                  TruthValue,
        swIfSingleHostViolationOperTrapEnable                   TruthValue,
        swIfSingleHostViolationOperTrapCount                    INTEGER,
        swIfSingleHostViolationAdminTrapFrequency               INTEGER,
        swIfLockLimitationMode                                  INTEGER,
        swIfLockMaxMacAddresses                                 INTEGER,
        swIfLockMacAddressesCount                               INTEGER,
        swIfAdminSpeedDuplexAutoNegotiationLocalCapabilities    AutoNegCapabilitiesBits,
        swIfOperSpeedDuplexAutoNegotiationLocalCapabilities     AutoNegCapabilitiesBits,
        swIfSpeedDuplexNegotiationRemoteCapabilities            AutoNegCapabilitiesBits,
        swIfAdminComboMode                                      INTEGER,
        swIfOperComboMode                                       INTEGER,
        swIfAutoNegotiationMasterSlavePreference                INTEGER
    }


swIfIndex OBJECT-TYPE
    SYNTAX   INTEGER
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Index to the swIfTable. The interface defined by a
         particular value of this index is the same interface as
         identified by the same value of ifIndex (MIB II)."
    ::= {  swIfEntry 1  }

swIfPhysAddressType OBJECT-TYPE
    SYNTAX  INTEGER {
        default(1),
        reserve(2)
    }
    MAX-ACCESS  read-write
    STATUS      obsolete
    DESCRIPTION
        " This variable indicates whether the physical address assigned to this
          interface should be the default one or be chosen from the set of
          reserved physical addresses of the device."
    DEFVAL { default }
    ::= {  swIfEntry 2  }

swIfDuplexAdminMode  OBJECT-TYPE
    SYNTAX  INTEGER {
        none(1),
        half(2),
        full(3)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable specifies whether this interface should operate in
         half duplex or full duplex mode. This specification will take effect
         only if swIfSpeedDuplexAutoNegotiation is disabled.
         A value of 'none' is returned if a value of the variable
         hasn't been set."
    DEFVAL { none }
    ::= {  swIfEntry 3  }

swIfDuplexOperMode  OBJECT-TYPE
    SYNTAX  INTEGER {
        half(1),
        full(2),
        hybrid(3),
        unknown(4)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        " This variable indicates whether this interface operates in half
          duplex or full duplex mode.
          This variable can have the values hybrid or unknown
          only for a trunk.
          unknown - only if trunk operative status is not present."
    ::= {  swIfEntry 4  }

swIfBackPressureMode OBJECT-TYPE
    SYNTAX  INTEGER {
        enable(1),
        disable(2)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates whether this interface activates back pressure
         when congested."
    ::= {  swIfEntry 5 }

swIfTaggedMode OBJECT-TYPE
    SYNTAX  INTEGER {
        enable(1),
        disable(2)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "If enable, this interface operates in tagged mode, i.e all frames sent
         out through this interface will have the 802.1Q header.
         If disabled the frames will not be tagged."
    DEFVAL { disable }
    ::= {  swIfEntry 6 }

swIfTransceiverType  OBJECT-TYPE
    SYNTAX  INTEGER {
        regular(1),
        fiberOptics(2),
        comboRegular(3),
        comboFiberOptics(4)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        " This variable indicates the transceiver type of this interface."
    ::= {  swIfEntry 7  }

swIfLockAdminStatus OBJECT-TYPE
    SYNTAX  INTEGER {
       locked(1),
       unlocked(2)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates whether this interface should operate in locked
         or unlocked mode.
         In unlocked mode the device learns all MAC addresses from this port and
         forwards all frames arrived at this port. In locked mode no new MAC
         addresses are learned and only frames with known source MAC
         addresses are forwarded."
    DEFVAL { unlocked }
    ::= {  swIfEntry 8 }

swIfLockOperStatus OBJECT-TYPE
    SYNTAX  INTEGER {
        locked(1),
        unlocked(2)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable defines whether this interface operates in locked
         or unlocked mode. It is locked in each of the following two cases:
             1) if swLockAdminStatus  is set to locked
             2) no IP/IPX interface is defined over this interface and no
                VLAN contains this interface.
         In unlocked mode the device learns all MAC addresses from this port and
         forwards all frames arrived at this port. In locked mode no new MAC
         addresses are learned and only frames with known source MAC
         addresses are forwarded."
    ::= {  swIfEntry 9 }

swIfType  OBJECT-TYPE
    SYNTAX  INTEGER {
        eth10M(1),
        eth100M(2),
        eth1000M(3),
        eth10G(4),
        unknown(5)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        " This variable specifies the type of interface."
    ::= {  swIfEntry 10 }

swIfDefaultTag  OBJECT-TYPE
    SYNTAX  INTEGER (0..4095)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable specifies the default VLAN tag which will be attached
         to outgoing frames if swIfTaggedMode for this interface is enabled."
    DEFVAL { 0 }
    ::= {  swIfEntry 11 }

swIfDefaultPriority  OBJECT-TYPE
    SYNTAX  INTEGER (0..7)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        " This variable specifies the default port priority."
    DEFVAL { 0 }
    ::= { swIfEntry 12 }

swIfStatus OBJECT-TYPE
   SYNTAX  RowStatus
   MAX-ACCESS   read-write
   STATUS       current
   DESCRIPTION
       "The status of a table entry.
        It is used to delete an entry from this table."
  ::= { swIfEntry 13 }

swIfFlowControlMode OBJECT-TYPE
   SYNTAX  INTEGER {
      on(1),
      off(2),
      autoNegotiation(3),
      enabledRx(4),
      enabledTx(5)
   }
   MAX-ACCESS   read-write
   STATUS       current
   DESCRIPTION
       "on - Flow control will be enabled on this interface according to the
             IEEE 802.3x standard.
        off - Flow control is disabled.
        autoNegotiation - Flow control will be enabled or disabled on this
                          interface. If enabled, it will operate as specified
                          by the IEEE 802.3x standard.
        enabledRx - Flow control will be enabled on this interface for
                    recieved frames.
        enabledTx - Flow control will be enabled on this interface for
                    transmitted frames.
        An attempt to set this object to 'enabledRx(4)' or 'enabledTx(5)'
        will fail on interfaces that do not support operation
        at greater than 100 Mb/s.
        In any case, flow control can work only if swIfDuplexOperMode is
        full."
   ::= { swIfEntry  14}

swIfSpeedAdminMode OBJECT-TYPE
   SYNTAX  INTEGER
   MAX-ACCESS   read-write
   STATUS       current
   DESCRIPTION
        "This variable specifies the required speed of this interface in bits
         per second. This specification will take effect only if
         swIfSpeedDuplexAutoNegotiation is disabled.
         A value of 10 is returned for 10G.
         A value of 0 is returned if the value of the variable
         hasn't been set."
   DEFVAL { 0 }
  ::= { swIfEntry  15 }

swIfSpeedDuplexAutoNegotiation OBJECT-TYPE
   SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
   }
   MAX-ACCESS   read-write
   STATUS       current
   DESCRIPTION
       "If enabled the speed and duplex mode will be set by the device through
       the autonegotiation process. Otherwise these characteristics will be
       set according to the values of swIfSpeedAdminMode and
       swIfSpeedDuplexAutoNegotiation."
  ::= { swIfEntry 16 }

swIfOperFlowControlMode OBJECT-TYPE
   SYNTAX  INTEGER {
      on(1),
      off(2),
      enabledRx(3),
      enabledTx(4)
   }
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
       "on - Flow control is enabled on this interface according to the
             IEEE 802.3x standard.
        off - Flow control is disabled.
        enabledRx - Flow control is enabled on this interface for
                    recieved frames.
        enabledTx - Flow control is enabled on this interface for
                    transmitted frames."
  ::= { swIfEntry  17}

swIfOperSpeedDuplexAutoNegotiation OBJECT-TYPE
   SYNTAX  INTEGER {
        enabled(1),
        disabled(2),
        hybrid(3),
        unknown(4)
   }
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
       "If enabled the speed and duplex are determined by the device through
       the autonegotiation process.
       If disabled these characteristics are determined according to the values
       of swIfSpeedAdminMode and swIfDuplexAdminMode.
       hybrid - only for a trunk.
       unknown -  only for ports that there operative status is not present."
  ::= { swIfEntry 18 }

swIfOperBackPressureMode OBJECT-TYPE
    SYNTAX  INTEGER {
        enable(1),
        disable(2),
        hybrid(3),
        unknown(4)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable indicates the operative back pressure mode of
         this interface."
    ::= {  swIfEntry 19 }

swIfAdminLockAction OBJECT-TYPE
    SYNTAX  INTEGER {
        discard(1),
        forwardNormal(2),
        discardDisable(3)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates which action this interface should be taken
        in locked mode and therefore relevant only in locked mode.
        Possible actions:
        discard(1) - every packet is dropped.
        forwardNormal(2) - every packet is forwarded according to the DST address.
        discardDisable(3) - drops the first packet and suspends the port."
    --DEFVAL { discard } changed to product specific
    ::= {  swIfEntry 20 }


swIfOperLockAction OBJECT-TYPE
    SYNTAX  INTEGER {
        discard(1),
        forwardNormal (2),
        discardDisable(3)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable indicates which action this interface actually takes in
        locked mode and therefore relevant only in locked mode.
        Possible actions:
        discard(1) - every packet is dropped.
        forwardNormal(2) - every packet is forwarded according to the DST address.
        discardDisable(3) - drops the first packet and suspends the port."
    ::= {  swIfEntry 21 }


swIfAdminLockTrapEnable OBJECT-TYPE
    SYNTAX  TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates whether to create a SNMP trap in the locked mode."
    --DEFVAL { false } changed to product specific
    ::= {  swIfEntry 22 }

swIfOperLockTrapEnable OBJECT-TYPE
    SYNTAX  TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable indicates whether a SNMP trap can be created in the
        locked mode."
    ::= {  swIfEntry 23 }

swIfOperSuspendedStatus OBJECT-TYPE
    SYNTAX  TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable indicates whether the port is suspended or not due to some
        feature. After reboot this value is false"
    ::= {  swIfEntry 24 }

swIfLockOperTrapCount  OBJECT-TYPE
    SYNTAX  INTEGER (0 .. 2147483647 )
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable indicates the trap counter status per ifIndex
        (i.e. number of received packets since the last trap sent due to a
        packet which was received on this ifIndex). It's relevant only in locked
        mode while trap is enabled."
    ::= {  swIfEntry 25 }

swIfLockAdminTrapFrequency OBJECT-TYPE
    SYNTAX  INTEGER (1 .. 1000000)
--    UNITS    "seconds"
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates the minimal frequency (in seconds) of sending
        a trap per ifIndex. It's relevant only in locked  mode and in trap
        enabled."
    --DEFVAL { 10 } changed to product specific
    ::= {  swIfEntry 26 }

swIfReActivate OBJECT-TYPE
    SYNTAX  TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable reactivates (enables) an ifIndex (which was suspended)"
    DEFVAL { false }
    ::= {  swIfEntry 27 }

swIfAdminMdix OBJECT-TYPE
   SYNTAX  INTEGER {
      cross(1),
      normal(2),
      auto(3)
   }
   MAX-ACCESS   read-write
   STATUS       current
   DESCRIPTION
       "The configuration is on a physical port, not include trunks.
        cross  - The interface should force crossover.
        normal - The interface should not force crossover.
        auto    - Auto mdix is enabled on the interface."
   ::= { swIfEntry 28 }

swIfOperMdix OBJECT-TYPE
   SYNTAX  INTEGER {
      cross(1),
      normal(2),
      unknown(3)
   }
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
       "cross  - The interface is in crossover mode.
        normal - The interface is not in crossover mode.
        unknown - Only for port that its operative status is not present
                  or down."
   ::= { swIfEntry 29 }

swIfHostMode OBJECT-TYPE
    SYNTAX  INTEGER {
       single(1),
       multiple(2),
       multiple-auth(3)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates the 802.1X host mode of a port. Relevant when the port's 802.1X control is auto.
        In addtion multiple-auth was added."
    DEFVAL { single }
    ::= {  swIfEntry 30 }

swIfSingleHostViolationAdminAction OBJECT-TYPE
    SYNTAX  INTEGER {
       discard(1),
       forwardNormal (2),
       discardDisable(3)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates which action this interface should take in single authorized.
        Possible actions:
        discard - every packet is dropped.
        forwardNormal - every packet is forwarded according to the DST address.
        discardDisable - drops the first packet and suspends the port."
    DEFVAL { discard }
    ::= {  swIfEntry 31 }

swIfSingleHostViolationOperAction OBJECT-TYPE
    SYNTAX  INTEGER {
       discard(1),
       forwardNormal (2),
       discardDisable(3)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable indicates which action this interface actually takes in single authorized.
        Possible actions:
        discard(1) - every packet is dropped.
        forwardNormal(2) - every packet is forwarded according to the DST address.
        discardDisable(3) - drops the first packet and suspends the port."
    DEFVAL { discard }
    ::= {  swIfEntry 32 }

swIfSingleHostViolationAdminTrapEnable OBJECT-TYPE
    SYNTAX  TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates whether to create a SNMP trap in single authorized."
    DEFVAL { false }
    ::= {  swIfEntry 33 }

swIfSingleHostViolationOperTrapEnable OBJECT-TYPE
    SYNTAX  TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable indicates whether a SNMP trap can be created in the single authorized."
    ::= {  swIfEntry 34 }

swIfSingleHostViolationOperTrapCount OBJECT-TYPE
    SYNTAX  INTEGER (0 .. 2147483647)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable indicates the trap counter status per ifIndex
        (i.e. number of received packets since the last trap sent due to a packet
        which was received on this ifIndex). It's relevant only in single authorized
        while trap is enabled."
    ::= {  swIfEntry 35 }

swIfSingleHostViolationAdminTrapFrequency OBJECT-TYPE
    SYNTAX  INTEGER (0 .. 1000000)
 -- UNITS    "seconds"
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates the minimal frequency (in seconds) of sending a
        trap per ifIndex. It's relevant only in single authorized and in trap enabled.
        A value of 0 means that trap is disabled."
    DEFVAL { 0 }
    ::= {  swIfEntry 36 }

swIfLockLimitationMode OBJECT-TYPE
    SYNTAX  INTEGER {
        disabled(1),
        dynamic(2),
        secure-permanent(3),
        secure-delete-on-reset(4)
    }
    MAX-ACCESS   read-write
    STATUS   current
    DESCRIPTION
        "This variable indicates what is the learning limitation on the locked interface.
        Possible values:
        disabled - learning is stopped. The dynamic addresses associated with the
            port are not aged out or relearned on other port as long as the port is
            locked.
        dynamic - dynamic addresses can be learned up to the maximum dynamic addresses
            allowed on the port. Relearning and aging of the dynamic addresses are
            enabled. The learned addresses aren't kept after reset.
        secure-permanent - secure addresses can be learned up to the maximum addresses
            allowed on the port. Relearning and aging of addresses are disabled.
            The learned addresses are kept after reset.
        secure-delete-on-reset - secure addresses can be learned up to the maximum addresses
            allowed on the port. Relearning and aging of addresses are disabled.
            The learned addresses are not kept after reset."
    --DEFVAL { disabled } changed to product specific
    ::= {  swIfEntry 37 }

swIfLockMaxMacAddresses OBJECT-TYPE
    SYNTAX  INTEGER (0 .. 2147483647)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable defines the maximum number of dynamic addresses that
        can be asscoiated with the locked interface. It isn't relevant in
        disabled limitation mode."
    DEFVAL { 1 }
    ::= {  swIfEntry 38 }

swIfLockMacAddressesCount OBJECT-TYPE
    SYNTAX  INTEGER (0 .. 2147483647)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable indicates the actual number of dynamic addresses that can
        be asscoiated with the locked interface. It isn't relevant in disabled
        limitation mode."
    ::= {  swIfEntry 39 }

swIfAdminSpeedDuplexAutoNegotiationLocalCapabilities OBJECT-TYPE
    SYNTAX AutoNegCapabilitiesBits
    MAX-ACCESS   read-write
    STATUS       current
    DESCRIPTION
        "Administrative auto negotiation capabilities of the interface that can be advertised when
        swIfSpeedDuplexAutoNegotiation is enabled.
        default bit means advertise all the port's capabilities
        according to its type."
    DEFVAL { {default} }
    ::= { swIfEntry 40 }

swIfOperSpeedDuplexAutoNegotiationLocalCapabilities OBJECT-TYPE
    SYNTAX AutoNegCapabilitiesBits
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Operative auto negotiation capabilities of the remote link.
        unknown bit means that port operative status is not up."
    ::= { swIfEntry 41 }

swIfSpeedDuplexNegotiationRemoteCapabilities OBJECT-TYPE
    SYNTAX AutoNegCapabilitiesBits
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Operative auto negotiation capabilities of the remote link.
        unknown bit means that port operative status is not up,
        or auto negotiation process not complete,
        or remote link is not auto negotiation able."
    ::= { swIfEntry 42 }

swIfAdminComboMode  OBJECT-TYPE
    SYNTAX  INTEGER {
        force-fiber(1),
        force-copper(2),
        prefer-fiber(3),
        prefer-copper(4)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable specifies the administrative mode of a combo Ethernet interface."
    DEFVAL { prefer-fiber }
    ::= {  swIfEntry 43  }

swIfOperComboMode  OBJECT-TYPE
    SYNTAX  INTEGER {
        fiber(1),
        copper(2),
        unknown(3)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This variable specifies the operative mode of a combo Ethernet interface."
    ::= {  swIfEntry 44  }

swIfAutoNegotiationMasterSlavePreference OBJECT-TYPE
    SYNTAX  INTEGER {
        preferMaster(1),
        preferSlave(2)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable specifies the administrative mode of the Maste-Slave preference in auto negotiation."
--    DEFVAL - according to MTSC parameter
    ::= {  swIfEntry 45 }



--
-- swIfMibVersion
--
swIfMibVersion OBJECT-TYPE
    SYNTAX  INTEGER
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The swIfTable Mib's version, the current version is 3."
    ::= { swInterfaces 2 }


--
-- swIfPortLockSupport
--
swIfPortLockSupport OBJECT-TYPE
    SYNTAX  INTEGER {
        supported (1),
        notSupported (2)
    }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "indicates if the locked port package is supported."
    ::= { swInterfaces 3 }


--
-- swIfPortLockActionSupport
--
swIfPortLockActionSupport OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(1))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "indicates which port lock actions are supported:
                (bit 0 is the most significant bit)
            bit 0 - discard
            bit 1 - forwardNormal
            bit 2 - discardDisable"
    ::= { swInterfaces 4 }


--
-- swIfPortLockTrapSupport
--
swIfPortLockTrapSupport OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(1))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "indicates with which port lock actions the trap option is supported
        (e.g. discard indicates that trap is supported only when the portlock
         action is discard):
                (bit 0 is the most significant bit)
            bit 0 - discard
            bit 1 - forwardNormal
            bit 2 - discardDisable"
    ::= { swInterfaces 5 }



--
-- swIfPortLockIfRangeTable
--
swIfPortLockIfRangeTable    OBJECT-TYPE
   SYNTAX  SEQUENCE  OF SwIfPortLockIfRangeEntry
   MAX-ACCESS   not-accessible
   STATUS       current
   DESCRIPTION
    "Port lock interfaces range configuration"
   ::=  { swInterfaces 6 }

swIfPortLockIfRangeEntry OBJECT-TYPE
   SYNTAX  SwIfPortLockIfRangeEntry
   MAX-ACCESS   not-accessible
   STATUS       current
   DESCRIPTION
    "Defines the contents of each line in the swIfPortLockIfRangeTable table."
   INDEX   { swIfPortLockIfRangeIndex }
   ::=  { swIfPortLockIfRangeTable 1 }

SwIfPortLockIfRangeEntry ::= SEQUENCE {
        swIfPortLockIfRangeIndex           INTEGER,
        swIfPortLockIfRange                PortList,
        swIfPortLockIfRangeLockStatus      INTEGER,
        swIfPortLockIfRangeAction          INTEGER,
        swIfPortLockIfRangeTrapEn          TruthValue,
        swIfPortLockIfRangeTrapFreq        INTEGER
    }

swIfPortLockIfRangeIndex OBJECT-TYPE
    SYNTAX   INTEGER
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Index to the swIfPortLockIfRangeTable."
    ::= {  swIfPortLockIfRangeEntry 1  }

swIfPortLockIfRange OBJECT-TYPE
    SYNTAX      PortList
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The set of interfaces to which the port lock parameters should be configured"
    ::= { swIfPortLockIfRangeEntry 2 }

swIfPortLockIfRangeLockStatus OBJECT-TYPE
    SYNTAX  INTEGER {
       locked(1),
       unlocked(2)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates whether the interfaces range should operate in locked
         or unlocked mode.
         In unlocked mode the device learns all MAC addresses from these interfaces and
         forwards all frames arrived at these interfaces. In locked mode no new MAC
         addresses are learned and only frames with known source MAC
         addresses are forwarded."
    DEFVAL { unlocked }
    ::= { swIfPortLockIfRangeEntry 3 }

swIfPortLockIfRangeAction OBJECT-TYPE
    SYNTAX  INTEGER {
        discard(1),
        forwardNormal(2),
        discardDisable(3)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates which action for these interfaces should be take
        in locked mode and therefore relevant only in locked mode.
        Possible actions:
        discard(1) - every packet is dropped.
        forwardNormal(2) - every packet is forwarded according to the DST address.
        discardDisable(3) - drops the first packet and suspends the port."
    --DEFVAL { discard } changed to product specific
    ::= {  swIfPortLockIfRangeEntry 4 }

swIfPortLockIfRangeTrapEn OBJECT-TYPE
    SYNTAX  TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates whether to create a SNMP trap in the locked mode."
    --DEFVAL { false } changed to product specific
    ::= {  swIfPortLockIfRangeEntry 5 }

swIfPortLockIfRangeTrapFreq OBJECT-TYPE
    SYNTAX  INTEGER (1 .. 1000000)
--    UNITS    "seconds"
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This variable indicates the minimal frequency (in seconds) of sending
        a trap for these interfaces. It's relevant only in locked  mode and in trap
        enabled."
    --DEFVAL { 10 } changed to product specific
    ::= {  swIfPortLockIfRangeEntry 6 }

--
-- swIfExtTable
--

swIfExtTable    OBJECT-TYPE
    SYNTAX  SEQUENCE  OF SwIfExtEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "Display information and configuration of the device interfaces."
    ::=  { swInterfaces 7 }

swIfExtEntry OBJECT-TYPE
    SYNTAX  SwIfExtEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "Defines the contents of each row in the swIfExtTable."
    INDEX   { ifIndex }
    ::=  { swIfExtTable 1 }

SwIfExtEntry ::= SEQUENCE {
        swIfExtSFPSpeed    INTEGER
    }

swIfExtSFPSpeed OBJECT-TYPE
    SYNTAX  INTEGER {
        default(1),
        eth100M(2),
        eth1G(3)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Configure speed of an SFP Ethernet interface."
    DEFVAL { default }
    ::= {  swIfExtEntry 1  }

--
-- rlIfInterfaces
--

rlIfMibVersion OBJECT-TYPE
    SYNTAX  INTEGER
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "MIB's version, the current version is 1."
    ::= { rlIfInterfaces 1 }

rlIfNumOfPhPorts OBJECT-TYPE
    SYNTAX INTEGER
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Total number of physical ports on this device
         (including all stack units)"
    ::= { rlIfInterfaces 2 }

rlIfMapOfOnPhPorts OBJECT-TYPE
    SYNTAX OCTET STRING
    MAX-ACCESS          read-only
    STATUS      current
    DESCRIPTION
       "Each bit in this octet string indicates that the correspondig port's
        ifOperStatus is ON if set.
        The mapping of port number to bits in this octet string is as follows:
        The port with the L2 interface number 1 is mapped to the least
        significant bit of the 1st octet, the port with L2 ifNumber 2 to the
        next significant bit in the 1st octet, port 8 to the most-significant
        bit of the in the 1st octet, port 9 to the least
        significant bit of the 2nd octet, etc. and in general,
        port n to bit corresponding to 2**((n mod 8) -1) in byte n/8 + 1"
    ::= { rlIfInterfaces 3 }

rlIfClearPortMibCounters OBJECT-TYPE
    SYNTAX      PortList
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Each bit that is set in this portList represent a port that
         its mib counters should be reset."
    ::= { rlIfInterfaces 4 }

rlIfNumOfUserDefinedPorts OBJECT-TYPE
    SYNTAX INTEGER
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The number of user defined ports on this device."
    ::= { rlIfInterfaces 5 }

rlIfFirstOutOfBandIfIndex OBJECT-TYPE
    SYNTAX INTEGER
    MAX-ACCESS          read-only
    STATUS      current
    DESCRIPTION
        "First ifIndex of out-of-band port.
         This scalar exists only the device has out of band ports."
    ::= { rlIfInterfaces 6 }

rlIfNumOfLoopbackPorts OBJECT-TYPE
    SYNTAX      INTEGER
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The number of loopback ports on this device."
    ::= { rlIfInterfaces 7 }

rlIfFirstLoopbackIfIndex OBJECT-TYPE
    SYNTAX INTEGER
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "First ifIndex of loopback port.
         This scalar will exists only if rlIfNumOfLoopbackPorts
         is different from 0."
    ::= { rlIfInterfaces 8 }

rlIfExistingPortList OBJECT-TYPE
    SYNTAX      PortList
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Indicates which ports/trunks exist in the system.
         It doesn't indicate which are present."
    ::= { rlIfInterfaces 9 }

rlIfBaseMACAddressPerIfIndex OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Indicates if the system will assign a unique MAC per Ethernet port or not."
    ::= { rlIfInterfaces 10 }

rlFlowControlCascadeMode OBJECT-TYPE
    SYNTAX      INTEGER {
        enabled(1),
        disabled(2)
        }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "enable disable flow control on cascade ports"
    ::= { rlIfInterfaces 11 }

rlFlowControlCascadeType OBJECT-TYPE
    SYNTAX      INTEGER {
        internalonly(1),
        internalexternal(2)
        }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "define which type of ports will be affected by flow control on cascade ports"
    ::= { rlIfInterfaces 12 }

rlFlowControlRxPerSystem OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "define if flow control RX is supported per system."
    ::= { rlIfInterfaces 13 }

rlCascadePortProtectionAction OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "As a result of this set all of the local cascade ports
         will stop being consider unstable and will be force up."
    ::= { rlIfInterfaces 14 }

rlManagementIfIndex OBJECT-TYPE
    SYNTAX      InterfaceIndex
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Specify L2 bound management interface index in a single IP address system
        when configurable management interface is supported."
    ::= { rlIfInterfaces 15 }

rlIfClearStackPortsCounters OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "As a result of this set all counters of
         all external cascade ports will be cleared."
    ::= { rlIfInterfaces 16 }

rlIfClearPortMacAddresses OBJECT-TYPE
    SYNTAX      InterfaceIndexOrZero
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
         "if port is non secure, its all dynamic MAC addresses are cleared.
          if port is secure, its all secure MAC addresses which have learned or configured are cleared."
    ::= { rlIfInterfaces 17 }

rlIfCutThroughPacketLength OBJECT-TYPE
    SYNTAX      INTEGER (257 .. 16383)
    MAX-ACCESS  read-write
--              Obsolete
    STATUS      current
    DESCRIPTION
        "The default packet length that is assigned to a packet in the
         Cut-Through mode."
    DEFVAL { 1522 }
    ::= { rlIfInterfaces 18 }

rlIfCutPriorityZero OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-Through for priority 0."
    DEFVAL { false }
    ::= { rlIfInterfaces 19 }

rlIfCutPriorityOne OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-Through for priority 1."
    DEFVAL { false }
    ::= { rlIfInterfaces 20 }

rlIfCutPriorityTwo OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-Through for priority 2."
    DEFVAL { false }
    ::= { rlIfInterfaces 21 }

rlIfCutPriorityThree OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-Through for priority 3."
    DEFVAL { false }
    ::= { rlIfInterfaces 22 }

rlIfCutPriorityFour OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-Through for priority 4."
    DEFVAL { false }
    ::= { rlIfInterfaces 23 }

rlIfCutPriorityFive OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-Through for priority 5."
    DEFVAL { false }
    ::= { rlIfInterfaces 24 }

rlIfCutPrioritySix OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-Through for priority 6."
    DEFVAL { false }
    ::= { rlIfInterfaces 25 }

rlIfCutPrioritySeven OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-Through for priority 7."
    DEFVAL { false }
    ::= { rlIfInterfaces 26 }

rlIfCutThroughTable    OBJECT-TYPE
   SYNTAX  SEQUENCE  OF RlIfCutThroughEntry
   MAX-ACCESS   not-accessible
   STATUS       current
   DESCRIPTION
    "Information and configuration of cut-through feature."
   ::=  { rlIfInterfaces 27 }

rlIfCutThroughEntry OBJECT-TYPE
   SYNTAX  RlIfCutThroughEntry
   MAX-ACCESS   not-accessible
   STATUS       current
   DESCRIPTION
    "Defines the contents of each line in the swIfTable table."
   INDEX   { swIfIndex }
   ::=  { rlIfCutThroughTable 1 }

RlIfCutThroughEntry ::= SEQUENCE {
        rlIfCutThroughPriorityEnable                            TruthValue,
        rlIfCutThroughUntaggedEnable                            TruthValue,
        rlIfCutThroughOperMode                                  TruthValue
    }

rlIfCutThroughPriorityEnable  OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-through for a priority for an interface."
    DEFVAL { false }
    ::= {  rlIfCutThroughEntry 1  }

rlIfCutThroughUntaggedEnable  OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Enable or disable cut-through for untagged packets for an interface."
    DEFVAL { false }
    ::= {  rlIfCutThroughEntry 2  }

rlIfCutThroughOperMode  OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Operational mode of spesific cut-through interface."
    ::= {  rlIfCutThroughEntry 3  }

rlCutThroughPacketLength OBJECT-TYPE
    SYNTAX      INTEGER
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The default packet length that is assigned to a packet in the
         Cut-Through mode."
    ::= { rlIfInterfaces 28 }

rlCutThroughPacketLengthAfterReset OBJECT-TYPE
    SYNTAX      INTEGER (257 .. 16383)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The default packet length that is assigned to a packet in the
         Cut-Through mode after reset."
    DEFVAL { 1522 }
    ::= { rlIfInterfaces 29 }

rlCutThroughEnable OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Cut-Through global enable mode."
    ::= { rlIfInterfaces 30 }

rlCutThroughEnableAfterReset OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Cut-Through global enable mode after reset."
    DEFVAL { false }
    ::= { rlIfInterfaces 31 }

rlFlowControlMode OBJECT-TYPE
    SYNTAX      INTEGER {
        send-receive(1),
        receive-only(2)
        }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "Define which mode will be enabled on flow control enabled ports.
        The interfaces with enabled flow control will receive pause frames, but will not send flow control pause
        frames
        Send-receive: The interfaces with enabled flow control will receive and send pause frames.
        Receive-only: The interfaces with enabled flow control will receive pause frames, but will not send flow
       control pause frames."

    ::= { rlIfInterfaces 32 }



END


